English translation for "tooth mesh"
|
- 轮齿啮合
Related Translations:
- Example Sentences:
| 1. | Finite element analysis of the multi - tooth meshing effect of three - ring gear reducer
三环减速器多齿啮合效应的有限元分析 | | 2. | The phenomenon of increased loading capacity caused by several contact teeth is called the multi - tooth meshing effect
我们将齿轮啮合过程中因多齿啮合而导致齿轮副承载能力提高的现象称为多齿啮合效应。 | | 3. | So , it is of great importance to study multi - tooth meshing effect of three - ring gear reducer to disclose the essence of high loading capacity of three - ring gear reducer , increase loading capacity , minimize design parameters and reduce manufacturing cost
因此,考虑三环传动中的多齿啮合效应对于揭示三环减速器大承载能力的本质、提高三环减速器的承载能力、缩小设计尺寸、降低制造成本具有重要的意义。 | | 4. | This paper deduced the involute gear total tooth profile equations of unsymmetric teeth with double pressure angles , proposed the calculation formulas of coordinates and load angle at the upper and lower points of single and double teeth mesh areas , and programmed the relevant parametric programs
摘要推导出双压力角非对称渐开线齿轮系统全齿廓方程，以及在单、双齿啮合上、下界点处坐标和载荷角的计算公式，编制了相应的参数化程序。 | | 5. | 3 , during the process of the gear teeth meshing , the film shape and pressure distribution have little difference . but , the temperatures have the distinctive changes as the engaged position is varied , which means that the temperatures as the increase in the rate of slide to roll
3 、在齿轮传动啮合过程中，压力分布和油膜形状无明显变化，但温升随啮合位置的不同呈显著变化，即温升随着滑滚比增大而增大;在单、双齿啮合交替处，摩擦系数达到极值，可达0 . 08 。 | | 6. | Aimed to the two deficiencies of three - ring gear transmission , the dissertation will analyze these two aspects . the first , according to the finite element model of gear pair of three - ring gear reducer , the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method , and the number of teeth contacted simultaneously , their load distribution characteristics and the von mises stress change are gained
针对三环减速器以上两点的不足之处,本文将对以下两方面进行分析:首先,本文以三环减速器齿轮副有限元模型为研究对象,利用有限单元法对三环减速器多齿啮合效应进行分析,得到三环减速器传动时的实际接触齿数、啮合齿载荷分配以及vonmises应力变化规律。 | | 7. | Translation modes are similarly independent of the rotational support stiffnesses . large contact ratio do not mean lower mesh force . if either the number of sun or ring gear is not multiple of planet gear , system will run effectively , with lower impaction of tooth mesh in and out
研究表明：扭转支撑刚度的变化影响系统的转动模态，径向支撑刚度(行星架的除外)的变化影响系统的位移模态；齿轮间重合度大并不等于轮齿间的受力情况好；行星轮与内齿圈齿数不为行星轮个数的整数被时，轮齿的啮入、啮出对系统的冲击小，系统的效率高。 |
- Similar Words：
- "tooth lock washer" English translation, "tooth lock washers" English translation, "tooth loss" English translation, "tooth margin" English translation, "tooth mark" English translation, "tooth mesh leakage" English translation, "tooth microphone" English translation, "tooth migration" English translation, "tooth mill" English translation, "tooth mobility" English translation
|
|
|
